![]() The next time the error occurs I should have a cleaner set of codes (for example, I replaced a wheel speed sensor 2 weeks ago but I didn't clear the memory after installing it).Ģ38 Misfire : cylinder 1 (note: I've seen this one before over the years) I know some won't be relevant since they could have been stored from unrelated issues. Hopefully, someone can make some sense out of these error codes to see if there's anything that points to a specific part. I rarely start a new thread but after searching for hours, most thread responses were "What were the codes?", "We need the codes to help." but since no one followed up by listing any codes, there were no definitive solutions posted.Īfter reading the module error codes (posted below) I cleared them from memory and everything seems to be working properly again with no warning lights. It's the one with the gear and exclamation mark (or "TRANS.FAILSAFE PROG" on dashboards with the MID). I've got the "Automatic Transmission" warning light on. ![]() I'll look into that but if anyone has any advice, let me know. I suspect there's an intermittent problem with the crankshaft speed sensor or circuit. The current status is that clearing the codes has the car working normally again. I also had an IKE code 141 "ATS Signal: telegram error or no telegram" but I'm pretty sure that was a remnant from a turn signal bulb problem about a week ago that has been corrected. (Notice no more 227 and 228 codes - I know it's unrelated to the transmission but solving them was a big deal for me). I'll post the details of that on another thread.īack to the transmission "limp mode" and warning light. They were always there and now they're not. It seemed to solve the 227 and 228, lambda contol tolerance Banks 1 and 2 codes I was getting regularly over the last several years. This kit (maybe the o-ring alone) made an amazing difference in the power the car has. *********************************************************************ġ88 Lambda probe heating upstrem sensor 1Īfter about a month of everything running great, the car returned to limp mode a couple of days ago.īefore I go into the detail about the current issue, I want to say something good about the DISA repair kit created by Gary at German Auto Solutions. Cluster - Status: ERROR !ĨD EGS Data lead disturbed (Note: Interesting ***8211 Where is the EGS located?) Single diagnosis DME / DDE - Status: ERROR !ħ4 A/C-compressor relay (note: A/C is working fine)Ģ38 Misfire : cylinder 1 (note: I***8217 ve seen this one before over the years)ġ68 Pedal position sensor potentiometer supply channel 1Ģ28 Mixture Deviation : bank 2 (Have had these before too)ġ49 CAN ABS/DSC wheel speeds (Note: remnant from before I replaced a wheel speed sensor)ġ50 CAN-BUS : time-out (signal not sent during initialization) I added some of my own notes next to the codes. The next time the error occurs I should have a cleaner set of codes (for example, I replaced a wheel speed sensor 2 weeks ago but I didn***8217 t clear the memory after installing it). I know some won***8217 t be relevant since they could have been stored from unrelated issues. ![]() Hopefully, someone can make some sense out of these error codes to see if there***8217 s anything that points to a specific part. Others have called this safe mode or limp mode.Īfter reading the module error codes (posted below) I cleared them from memory and everything seems to be working properly again with no warning lights. The steptronic mode worked allowing manual shifts from 1st to 5th gear (also harsh shifts). The shifts were very harsh (both upshifts and downshifts). There seems to be less torque on initial acceleration but the automatic transmission seems to shift through all gears. The car takes longer than normal to start and the initial idle can be a little rough. The Service Engine Soon light was also lit. The gear and exclamation mark warning light was lit. I rarely start a new thread but after searching for hours, most thread responses were ***8220 What were the codes?***8221, ***8220 We need the codes to help.***8221 but since no one followed up by listing any codes, there were no definitive solutions posted. It***8217 s the one with the gear and exclamation mark (or "TRANS.FAILSAFE PROG" on dashboards with the MID). ![]() I***8217 ve got the ***8220 Automatic Transmission***8221 warning light on.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |